jp_'s Profile

jp_

Account Details
SteamID64	76561198032914094
SteamID3	[U:1:72648366]
SteamID32	STEAM_0:0:36324183
Country	United States
Signed Up	September 7, 2012
Last Posted	July 18, 2024 at 12:39 AM
Posts	691 (0.2 per day)

Game Settings
In-game Sensitivity	.5 w/ mouse accel
Windows Sensitivity	6/11
Raw Input	1
DPI	1800
Resolution	1920x1080
Refresh Rate	120hz lightboost

Hardware Peripherals
Mouse	repaired g400, thanks megawac
Keyboard	filco ninja browns
Mousepad	artisan hien
Headphones	samson sr850
Monitor	asus vg248qe

1 ⋅⋅ 3 4 5 6 7 8 9 ⋅⋅ 46

#14 Fps maxed at 60 in Q/A Help

What operating system are you on?

Also what are your hardware specs.

posted about 9 years ago

#8 Hard drive 100% usage in Hardware

try disabling disk write caching.
What's the amount of FREE ram from task manager?

posted about 9 years ago

#23 Monitor freaks out when watching videos sometimes in Hardware

delpoOn driver 13.12 now, still having the problem :\

Have you disabled hardware acceleration on both flash and the browser?

posted about 9 years ago

#20 Monitor freaks out when watching videos sometimes in Hardware

I had the same problem too and since downgrading from 14.0 driver to 13.12, videos no longer causes my screen to go nuts.

posted about 9 years ago

#271 HUD editing: short questions, quick answers in Customization

Is there a way to disable the delay for players's own kills in the kill feed and have it flow with the kill feed?

posted about 10 years ago

#11 Slight freezes in Q/A Help

is the stuttering exclusive a game mode or everywhere?

posted about 10 years ago

#1 JJP looking to backup for ESEA open in Recruitment (looking for team)

Hi, I'm JJP.

I play scout.
My schedule isn't very good but I can play Mon-Thurs,Sun 6PM to ~~2AM~~ 8PM[/s] PST (West coast).

I've got two seasons of ESEA open, so high-mid open. I can pay my own fees as well.

I'm hoping to join a team without negativity issues and one that never settles for anything less than the best. Also doesn't get butt hurt to criticisms. As backup I'll still try to attend team meetings and would be down to review demos together.

EDIT: This is for the new/next season.

posted about 10 years ago

#2 Rubberband Lag Problem on TF2 in Q/A Help

Stay away from Firepowered Mge servers.

It lags for everyone.

posted about 10 years ago

#6 NVENC + obs in TF2 General Discussion

AMD's VCE encodes frames significantly slower than NVENC and QuickSync. I don't know about compression efficiency/image quality though..

While my (HD4000) quicksync can encode 1920x1080 frames at 130+
(HD7850) VCE struggles to pass 40.
The two are set to best quality preset @ 20mbps.

I used Msi afterburner for benchmark since it has support for hardware h.264 encoders.

posted about 10 years ago

#57 QL Accel Driver in TF2 General Discussion

povohatOffset is counts per millisecond

So the range would be from 0 to MAX polling rate?

Because my G400's (and deathadder's) rates fluctuate quite a bit..
I'm using MouseRate to check and it shows random +1000hz spikes while moving the mouse below speeds that would normally register has 1000hz.

Does the driver account for this?

posted about 10 years ago

#7 Gargleburry lft open in Recruitment (looking for team)

Mr_Owlopen is open is open

unless it's sandbag'd open. Which is invite IM open open.

posted about 10 years ago

#54 QL Accel Driver in TF2 General Discussion

soney"Offset (default 0):
Acceleration will not be applied until the mouse movement exceeds this velocity.
Negative values are supported, which has the effect of causing higher rates of
acceleration to happen at lower velocities"

...this velocity

velocity in what? m/s ? cm/360? pls help i am lost ;_;

I have trouble understanding the descriptions as well..
I think it's a sensitivity number? so acceleration will kick in once your cursor goes past the rate of movement which would be the offset value.

I don't use this since it seems to induce jerky motions during transitions.

posted about 10 years ago

#10 75 hz vs 60hz in Hardware

Lexhttp://www.monitortests.com/forum/Thread-Custom-Resolution-Utility-CRU

I used this tool to run my old LG monitor at 70Hz@1080p without artifacts. Some monitors will allow more, some less.

AT YOUR OWN RISK, find the highest stable value and see how it works. The difference between 60Hz and 70Hz isn't huge, but it's noticeable.

I used my old Acer monitor at 1680x1050 @ 86hz, was amazing till I got a 144hz monitor. Did notice how much hotter the monitor operated, surprised it STILL lasts. ~2 years.

also refer to your monitor's manual. Many monitors can run 1440x900@75hz.

posted about 10 years ago

#16 Shit to do when i'm bored in Off Topic

pick up blender

Very easy tutorial.
https://www.youtube.com/watch?v=y__uzGKmxt8

posted about 10 years ago

#13 Lightboost? in Hardware

MedusaThe input lag is not worth it imo.

Try a mouse without a huge click latency.

http://cdn.overclock.net/b/b3/b39b5899_response_test_overall_140718.png

http://utmalesoldiers.blogspot.com/2013/02/114.html

posted about 10 years ago

1 ⋅⋅ 3 4 5 6 7 8 9 ⋅⋅ 46